动臂塔式起重机利勃海尔
500 HC-L 16
L U F F I N G B O O M T O W E R C R A N E
stationary and travelling
Morrow Equipment
Hook Heights
10m 33 ft
5m 16 ft
0 5m 16 ft
10m 33 ft
15m 49 ft
20m 66 ft
25m 82 ft
30m 98 ft
35m 115 ft
40m 131 ft
500 HC-L 16
45m 148 ft 50m 164 ft 55m 180 ft 60m 197 ft
(70m)
(65m)
(55m)
(60m)
(50m)
(45m)
(40m)
(35m)
(30m)
(25m)
(20m)
(15m)
(10m)
(5m)
NOTE! By combining information from the graph above with data from the tower height chart on the adjacent page, hook heights can be deter-mined. It will be necessary to select boom length, boom angle and tower configuration. Contact Morrow for additional information.
Morrow Equipment Co., L.L.C.
D i r e c t i o n o f b o o m
500 HC-L 16
➜w h e n c l i m b i n g .
PLAN VIEW – showing tail swing radius and minimum clearance.
with 500 HC-L Tower Section
on concrete slab
with 500 HC-L Base Section
on concrete slab
T0WER HEIGHTS*
NOTE! Information regarding crane equipped for rail travelling is available. Consult operation manual or contact Morrow.
Morrow Equipment Co., L.L.C.
500 HC-L 1
6
maximum tower with 131 ft (40m)
boom installed*
Configuration Iwith 500 HC-L tower
FREESTANDING
stationary
*NOTE! Tower configurations illustrated above apply to cranes in which the "out of operation" boom angle is set at 70°. If the "out of operation" boom position is set at 15°, up to 2 additional tower sections may be added to tower configura-tion I, II and III. Consult operation manual. Contact Morrow for information regarding alternate tower configurations. Restrictions may apply.
Morrow Equipment Co., L.L.C.
Capacities
500 HC-L 16
70,550 lbs61,730 lbs52,910 lbs44,090 lbs35,270 lbs26,460 lbs17,640 lbs8,820 lbs70,550 lbs61,730 lbs52,910 lbs44,090 lbs35,270 lbs26,460 lbs17,640 lbs8,820 lbs70,550 lbs61,730 lbs52,910 lbs44,090 lbs35,270 lbs26,460 lbs17,640 lbs8,820 lbs15m 20m 25m 30m 35m 40m 45m 50m 55m 60m
Morrow Equipment Co., L.L.C.
IMPORTANT! crane.
500 HC-L 16
NOTE!
D i r e c t i o n o f b o o m NOTE! †
Contact Morrow for additional information regarding dimensions, alternate tower configura-tions, reactions forces, tie-in installation and slab opening requirements.
TOP CLIMBING
with 500 HC-L Tower
tied to structure
Morrow Equipment Co., L.L.C.
Hoist Speed and Capacity
500 HC-L 16
IMPORTANT! The data below applies only to crane serial no. 29.194
NOTE! Capacities and line speeds indicated will vary depending on the amount of hoist rope installed. This crane model may be equipped with a hoist unit other than that specified in the data above. To verify, check the serial number of the crane and refer to the Liebherr 500 HC-L 16 Operation Manual for additional information. One-part line operation is not available with crane serial number 29.194.
Motor Information
NOTE! Luffing speed figure above is for crane without load. Speed varies according to load on hook.
Power Requirements
Static: 480 Volts — 3-phase — 60 Hz — 350 Amperes — 245 kVATravelling: Information available upon request.
Specifications subject to change without prior notice. For additional information, contact Morrow Equipment.
Morrow Equipment Co., L.L.C.
500 HC-L 16
Slewing Assembly (Complete) includes turntable, swing motors, slewing ring and slewing ring support. Climbing shoes are detachable: add 800 lbs (365 kg) each for the two front shoes and 1,000 lbs (454 kg) each for the two back shoes, i. e., 3,600 lbs (1 638 kg) total. Dimensions and weight above do not include climbing shoes.2
Slewing Assembly Upper Part includes turntable and swing motors. Does not include slewing ring or slewing ring support.3
Slewing Assembly Lower Part includes slewing ring and slewing ring support. Does not include turntable or swing motors. Climbing shoes are detachable: add 800 lbs
(365 kg) each for the two front shoes and 1,000 lbs (454 kg) each for the two back shoes, i. e., 3,600 lbs (1 638 kg) total. Dimensions and weight above do not include climbing shoes.4
Machine deck can be split into two (2) parts: Inner part at 24,000 lbs (10 880 kg) and Outer part at 11,230 lbs (5 090 kg). 5
Does not include wire rope.6
A-frame (Complete) includes A-frame Part A, A-frame Part B (2 each), back stays (2 each), ladder and platforms.7
Ballast Rocker Assembly (Complete) includes Ballast Rocker Strut (2 each), ballast carrier and connecting rods (2 each).8
Can be broken down into two panels.9
Boom Assembly Part 1 includes Boom Butt Section, one Intermediate Section (621) and erection wire rope.10
Boom Assembly Part 2 includes boom sections and pendent bars. Does not include hoist wire rope or hook block.
1
O M P A N Y, L. L. C.
Atlanta, GA • Charlotte, NC • Chicago, IL • Dallas, TX • Denver, CO • Honolulu, HI • Houston, TX • Los Angeles, CA Las Vegas, NV • Millwood, NY • Pensacola, FL • St. Louis, MO • San Francisco, CA • Salem, OR • Seattle, WA • Miami, FL • Tampa, FL Washington, DC • Sydney, Australia • Wellington, New Zealand • Vancouver, BC, Canada • Toronto, ON, Canada • Mexico City, Mexico
Printed in the USA
MEC - 500HCL16 - rev2 - 0205 - PDF