模具专业英语
angular pin 角梢 baffle 调节阻板
angular pin 倾斜梢 baffle plate 折流档板
ball button 球塞套 ball plunger 定位球塞
ball slider 球塞滑块 binder plate 压板
blank holder 防皱压板 blanking die 落料冲头
bolster 上下模板 bottom board 浇注底板
bolster 垫板 bottom plate 下固定板
bracket 托架 bumper block 缓冲块
buster 堵口 casting ladle 浇注包
casting lug 铸耳 cavity 模穴(模仁)
cavity retainer plate 模穴托板 center pin 中心梢
clamping block 锁定块 coil spring 螺旋弹簧
cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓
core 心型 core pin 心型梢
cotter 开口梢 cross 十字接头
cushion pin 缓冲梢 diaphragm gate 盘形浇口
die approach 模头料道 die bed 型底
die block 块形模体 die body 铸模座
die bush 合模衬套 die button 冲模母模
die clamper 夹模器 die fastener 模具固定用零件
die holder 母模固定板 die lip 模唇
die plate 冲模板 die set 冲压模座
direct gate 直接浇口 dog chuck 爪牙夹头
dowel 定位梢 dowel hole 导套孔
dowel pin 合模梢 dozzle 辅助浇口
dowel pin 定位梢 draft 拔模锥度
draw bead 张力调整杆 drive bearing 传动轴承
ejection pad 顶出衬垫 ejector 脱模器
ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套
ejector pad 顶出垫 ejector pin 顶出梢
ejector plate 顶出板 ejector rod 顶出杆
ejector sleeve 顶出衬套 ejector valve 顶出阀
eye bolt 环首螺栓 filling core 椿入蕊
film gate 薄膜形浇口 finger pin 指形梢
finish machined plate 角形模板 finish machined round plate 圆形模板
fixed bolster plate 固定侧模板 flanged pin 带凸缘?
flash gate 毛边形浇口 flask 上箱
floating punch 浮动冲头 gate 浇口
gate land 浇口面 gib 凹形拉紧?
goose neck 鹅颈管 guide bushing 引导衬套
guide pin 导梢 guide post 引导柱
guide plate 导板 guide rail 导轨
head punch 顶?冲头 headless punch 直柄冲头
heavily tapered solid 整体模蕊盒 hose nippler 管接头
impact damper 缓冲器 injection ram 压射柱塞
inlay busher 嵌入衬套 inner plunger 内柱塞
inner punch 内冲头 insert 嵌件
insert pin 嵌件梢 king pin 转向梢
king pin bush 主梢衬套 knockout bar 脱模杵
land 合模平坦面 land area 合模面
leader busher 导梢衬套 lifting pin 起模顶?
lining 内衬 locating center punch 定位中心冲头
locating pilot pin 定位导梢 locating ring 定位环
lock block 压块 locking block 定位块
locking plate 定位板 loose bush 活动衬套
making die 打印冲子 manifold block 歧管档块
master plate 靠模样板 match plate 分型板
mold base 塑胶模座 mold clamp 铸模紧固夹
mold platen 模用板 moving bolster 换模保持装置
moving bolster plate 可动侧模板 one piece casting 整体铸件
parallel block 平行垫块 paring line
分模线
parting lock set 合模定位器 pass guide 穴型导板
peened head punch 镶入式冲头 pilot pin 导?
pin gate 针尖浇口 plate 衬板
pre extrusion punch 顶挤冲头 punch 冲头
puncher 推杆 pusher pin 衬套梢
rack 机架 rapping rod 起模杆
re-entrant mold 凹入模 retainer pin 嵌件梢
retainer plate 托料板 return pin 回位梢
riding stripper 浮动脱模器 ring gate 环型浇口
roller 滚筒 runner 流道
runner ejector set 流道顶出器 runner lock pin 流道拉梢
screw plug 头塞 set screw 固定螺丝
shedder 脱模装置 shim 分隔片
shoe 模座之上下模板 shoot 流道
shoulder bolt 肩部螺丝 skeleton 骨架
slag riser 冒渣口 slide(slide core) 滑块
slip joint 滑配接头 spacer block 间隔块
spacer ring 间隔环 spider 模蕊支架
spindle 主轴 sprue 注道
sprue bushing 注道衬套 sprue bushing guide 注道导套
sprue lock bushing 注道定位衬套 sprue puller 注道拉料?
spue line 合模线 square key 方键
square nut 方螺帽 square thread 方螺纹
stop collar 限位套 stop pin 止动梢
stop ring 止动环 stopper 定位停止梢
straight pin 圆柱? stripper bolt 脱料螺栓
stripper bushing 脱模衬套 stripper plate 剥料板
stroke end block 行程止梢 submarine gate 潜入式浇口
support pillar 支撑支柱/顶出支柱 support pin 支撑梢
supporting plate 托板 sweep templete 造模刮板
tab gate 辅助浇口 taper key 推拔键
taper pin 拔锥梢/锥形梢 teeming 浇注
three start screw 三条螺纹 thrust pin 推力销
tie bar 拉杵 tunnel gate 隧道形浇口
vent 通气孔 wortle plate 拉丝模板
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
(责任编辑:bz小编)
Surface Appearance 外观
Glossiness/gloss finish 光洁度
Matt finish/matt surface 毛面
Glass fiber rich surface/glass emergence on the surface 玻纤外露
Blooming/surface blooming 表面析出
White patches on surface 表面白斑
Silver marks/silver streak 银纹
Splay mark 水纹
Flow mark 流纹
W
eld line 溶结纹
Brittle/brittleness 脆
Bubbles/trapped gas 气泡
Void 孔
Burn marks 烧伤
FR failed 阻燃不合格
Flame rating V-2 阻燃V-2
Poor dispersion 分散不好
FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块
Pellet porous 粒子不密/蜜蜂窝
Low impact/tensile etc 物理性能低
High flow/filler content etc 流动性/填充…过高
Longs/fines/doubles 长粒/碎屑/连粒
Poor cut 粒形不好
Bristle/voids 表面有小气泡/孔
Glass bundles 玻纤结团
Product was rejected due to 产品不能接受因为…
High moisture level 高水分
Warpage/warped 翘曲
Shrinkage/shrink 收缩
Sink marks 缩影
Short shot/short molding 打不满
Distortion 变形
Over dimension 尺寸过大
Under dimension 尺寸过小
Flashing 飞边
Discoloration 变色
Off color 颜色差异
Flow rate 流动率
Viscous 粘
High flow 高流动
Low flow 低流动
Sticky 粘
Mold release 脱模
Antioxidant 抗氧剂
Flame retardant agent 阻燃剂
Heat stabilizer 热稳定剂
Chopped glass fiber 短切玻纤
Roving glass fiber 粗纱/长玻纤
Glass beads 玻璃微珠
Milled fiber 碾磨纤
Molybdenum disulfide/moly/MoS2 二硫化钼
Colorant 着色剂
Pigment 颜料
Dye 染料
Accepted product specification 接受产品规格
Approved our product 认可我们的产品
Re-set spec 重新定标准
Add in extra … 添加多一点…
Reduced … content 减少…含量
Dropped/reduced … by x% 减少…含量…%
Confirmed color standard 确认颜色标准
Approved color standard 认可颜色标准
Re-confirmed color standard 重新确认颜色标准
Qualified our product 认可我们的产品
Undergoing heat aging test 在做热老化实验
Product is under testing 产品在测试当中
Received first order 接了第一个定单
Expected to finish by … 预计在…完成
Expected order is xMT 预计定单量…吨
Estimated annual/monthly consumption 预计年/月用量
模具制造业相关名词中英文对照大全--3时间:2010-05-05 11:05来源:包装网收集 作者: 点击:24次
emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark f
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die he
ight range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉
dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒
pin销
lifter guide pin浮升导料销
guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
模具制造业相关名词中英文对照大全--2时间:2010-05-05 11:05来源:包装网收集 作者: 点击:9次
baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 club car高尔夫球车 capability能力 parameter参数 factor系数 phosp
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板
bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品
defective products不良品
finished products成品
disposed products处理品
barcode条形码
flow chart流程窗体
assembly组装
stamping
冲压
molding成型
spare parts=buffer备品
coordinate坐标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片
thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机
degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应
ram连杆
edge finder巡边器
concave 凹
convex凸
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金
magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill钻
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式
voller pin formality滚针形式
cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状
torque扭矩
spline=the multiple keys花键
quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的
moly high speed steel钼高速的
organic solvent有机溶剂
bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
模具制造业相关名词中英文对照大全--1时间:2010-05-05 11:05来源:包装网收集 作者: 点击:5次
padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查
end-user/using unit(department)
使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部-(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用-状况明细表
blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验
description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办
PCE assembly production schedule sheet
PCE组装厂生产排配表
model机钟
work order工令
revision版次
remark备注
production control confirmation生产确认
checked by初审
approved by核准
department部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock locater block
定位块
under cut=scrap chopper清角
active plate活动板