防火控制图符号英文
INTERNATIONAL MARITIME ORGANIZATION
E
IMO
ASSEMBLY 23rd session Agenda item 17
A 23/Res.95225 February 2004 Original: ENGLISH
Resolution A.952(23)
Adopted on 5 December 2003
(Agenda item 17)
GRAPHICAL SYMBOLS FOR SHIPBOARD FIRE CONTROL PLANS
THE ASSEMBLY,
RECALLING Article 15(i) of the Convention on the International Maritime Organization concerning the functions of the Assembly in relation to regulations and guidelines concerning maritime safety,
BEARING IN MIND that regulation II-2/15.2.4 of the International Convention for the Safety of Life at Sea (SOLAS), 1974, as amended, requires that fire control plans be permanently exhibited for the guidance of the ship’s officers and that a duplicate set of fire control plans or a booklet containing such plans be permanently stored in a prominently marked weathertight enclosure outside the deckhouse for the assistance of shore-side fire-fighting personnel,
RECOGNIZING that the use of international symbols for shipboard fire control plans would greatly increase their usefulness, both for the crew of the ship and for shore-based fire brigades,
RECALLING ALSO resolution A.654(16) on Graphical symbols for fire control plans,
NOTING that ISO had, in close co-operation with IMO, developed standard ISO 17631:2002 – Ships and marine technology – Shipboard plans for fire protection, life-saving appliances and means of escape, providing fire protection symbols which generally conform to the corresponding symbols set out in resolution A.654(16),
NOTING IN PARTICULAR that, through MSC/Circ.1050, Member Governments had been invited to bring standard ISO 17631:2002 to the attention of shipbuilders, shipowners, shipoperators, shipmasters, shore-based fire-fighting personnel and other parties concerned with the preparation or use of shipboard fire control plans, so that they might use it, on a voluntary basis, for the preparation or use of the shipboard fire control plans required by SOLAS regulation II-2/15.2.4, pending the outcome of the work related to the revision of resolution A.654(16),
For reasons of economy, this document is printed in a limited number. Delegates are
kindly asked to bring their copies to meetings and not to request additional copies.
A 23/Res.952 - 2 -
HAVING CONSIDERED the recommendation made by the Maritime Safety Committee at its seventy-seventh session, 1. ADOPTS the Graphical symbols for shipboard fire control plans, set out in the Annex to the present resolution; 2. URGES Governments to bring the aforementioned graphical symbols to the attention of shipbuilders, shipowners, shipoperators, shipmasters, shore-based fire-fighting personnel and other parties concerned with the preparation or use of shipboard fire control plans with a view to encouraging their use for the preparation of the shipboard fire control plans required by SOLAS regulation II-2/15.2.4, for ships constructed on or after 1 January 2004;
3. INVITES Governments to bring standard ISO 17631:2002 to the attention of shipbuilders, shipowners, shipoperators and shipmasters so that they may use the additional guidance contained therein for the preparation of shipboard fire control plans; 4. AGREES that ships constructed before 1 January 2004 may continue to carry fire control plans that use the graphical symbols contained in resolution A.654(16); 5. REQUESTS the Maritime Safety Committee to keep this resolution under review and to amend it as necessary.
1.1
- 3 - ANNEX
A 23/Res.952
GRAPHICAL SYMBOLS FOR SHIPBOARD FIRE CONTROL PLANS* Graphical symbols for structural fire protection
A-class division
1.2
B-class division
1.3
Main vertical zone
1.4
and should show the actual direction of the door.
Add WT to the right side of the symbol in the case of a watertight door. fire door
Add SWT to the right side of the symbol in the case of a semi-watertight door.
1.5
The symbol should be at the door position and should show the actual direction of the door. Add WT to the right side of the symbol in fire door the case of a watertight door.
Add SWT to the right side of the symbol in the case of a semi-watertight door.
*
A legend of symbols and explanations should be a constituent part of any fire control plan and contain a list of the graphical symbols used in the plan, together with the appropriate explanations, and may include additional special information such as the type of extinguishing media used in fixed fire-extinguishing systems.
A 23/Res.952 No. Graphical symbol 1.6
- 4 -
1.7
1.8
1.9
Comments on use
The symbol should be at the door position and should show the actual direction of the door. Add WT to the right side of the symbol in the case of a watertight door. door
Add SWT to the right side of the symbol in the case of a semi-watertight door.
The symbol should be at the door position and should show the actual direction of the door. Add WT to the right side of the symbol in the case of a watertight door. door
Add SWT to the right side of the symbol in the case of a semi-watertight door.
The symbol should be at the door position and should show the actual direction of the door.
A-class sliding Add WT to the right side of the symbol in fire door the case of a watertight door.
Add SWT to the right side of the symbol in the case of a semi-watertight door.
and should show the actual direction of the door.
B-class sliding Add WT to the right side of the symbol in fire door the case of a watertight door.
Add SWT to the right side of the symbol in the case of a semi-watertight door.
Reference
No. 1.10
Graphical symbol
- 5 -
Reference
A-class self-closing sliding fire door
A 23/Res.952
1.11
1.12
1.13
1.14
Comments on use
The symbol should be at the door position and should show the actual direction of the door.
Add WT to the right side of the symbol in the case of a watertight door.
Add SWT to the right side of the symbol in the case of a semi-watertight door.
The symbol should be at the door position and should show the actual direction of the door. B-class self-
closing sliding Add WT to the right side of the symbol in fire door the case of a watertight door.
Add SWT to the right side of the symbol in the case of a semi-watertight door.
Colour of the circle and a letter at the right follows: Ventilation A = blue for accommodation and service remote control or spaces;
shut-off
M = green for machinery spaces;
C = yellow for cargo spaces.
Remote control for skylight
Remote control for watertight doors or fire doors
Add WT to the right side of the symbol to indicate remote control for watertight doors or FD to indicate remote control for fire doors.
A 23/Res.952 No. 1.15
Graphical symbol
- 6 -
Reference
Fire damper
1.16
Closing device for ventilation inlet or outlet
1.17
Remote control
for fire damper(s)
Comments on use
Colour of the circle and a letter at the right follows:
A = blue for accommodation and service
spaces;
M = green for machinery spaces;
C = yellow for cargo spaces.
Identification number of the damper may be shown at the bottom of the symbol.
Colour of the circle and a letter at the right follows:
A = blue for accommodation and service
spaces;
M = green for machinery spaces;
C = yellow for cargo spaces.
Identification number of the closing device may be shown at the bottom of the symbol.
Colour of the circle and a letter at the right follows:
A = blue for accommodation and service
spaces;
M = green for machinery spaces;
C = yellow for cargo spaces.
Identification number of the damper may be shown.
No. 1.18
Graphical symbol
- 7 -
Reference
Remote control for closing device(s) for ventilation inlet and outlet
A 23/Res.952
Comments on use
Colour of the circle and a letter at the right follows:
A = blue for accommodation and service
spaces;
M = green for machinery spaces;
C = yellow for cargo spaces.
device(s) may be shown.
Graphical symbols for fire-protection appliances
No. 2.1
Graphical symbol
Reference
Fire protection appliances or structural fire protection plan
Comments on use
2.2
2.3
2.4
2.5
Remote control for fire pump(s)
Fire pump(s)
The type, quantity of water delivered per symbol or in the legend.
for emergency fire pump or fire pump supplied
by the emergency source of power
Emergency fire
pump
The type, quantity of water delivered per symbol or in the legend.
A 23/Res.952
No. Graphical symbol 2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
- 8 -
Reference
Fuel pump(s) remote shut-off
Comments on use
Lube oil pump(s) remote shut-off
Remote control for bilge pump(s)
Remote control for emergency bilge pump Remote control for fuel oil valves Remote control for lube oil valves
Remote control for fire pump valve(s)
Remote release
station
Indicate at the bottom of the symbol the should be colour coded in the lower part of the symbol and be indicated by a letter at grey – CO 2 for carbon dioxide or N for nitrogen, brown – H for gas other than CO2 or N (type of gas to be indicated), white – P for powder, green – W for water.
No. 2.14
- 9 - A 23/Res.952
Graphical symbol
Reference
International shore connection
Comments on use
2.15
2.16
2.17
Sprinkler section
valve
at the right side of the symbol.
equivalent water-extinguishing systems.
systems should be indicated in the legend.
Indicate the reference number of the valve at the right side of the symbol.
Fire main section Indicate the reference number of the valve
valve at the right side of the symbol.
Fire hydrant
2.18
2.19
2.20
Powder section
valve
Foam section
valve
Indicate the reference number of the valve at the right side of the symbol.
Fixed fire-extinguishing installation
Extinguishing media should be colour-coded in the centre part of the symbol and indicated by a letter on top of the symbol as follows: grey – CO 2 for carbon dioxide or N for nitrogen, yellow – F brown – H for gas other than CO2 or N (type of gas to be indicated), white – P for powder, green – W for water.
A 23/Res.952
No. Graphical symbol 2.21
2.22
- 10 -
Comments on use
symbol and indicated by a letter on top of the symbol as follows: grey – CO 2 for carbon dioxide or N for nitrogen, yellow – F for foam, brown – H for gas other than CO 2white – P for powder, green – W for water.
Extinguishing media should be colour-Fixed fire-coded in the centre part of the symbol and extinguishing indicated by a letter on top of the symbol bottle, placed in as follows: grey – CO 2 for carbon dioxide protected area or N for nitrogen, yellow – F brown – H for gas other than CO2 or N (type of gas to be indicated), white – P for powder, green – W for water.
High expansion Indicate at the bottom of the symbol the foam supply
protected space, if necessary.
trunk (outlet)
Indicate at the bottom of the symbol the protected space, if necessary.
Reference
Fixed fire-extinguishing battery
2.23
2.24
2.25
2.26
2.27
Water spray system valves
Inert gas installation
Monitor
Extinguishing media should be colour-coded in the centre part of the symbol and indicated by a letter on the right side of the symbol as follows: yellow – F for foam, white – P for powder, green – W for water. Indicate the hose length at the right side of the symbol; where only one type of hose is used, the information can be shown in the right side of the symbol as follows: yellow – F for foam, white – P for powder, green – W for water.
Fire hose and nozzle
No. 2.28
- 11 - A 23/Res.952
Graphical symbol
Reference
Fire extinguisher
2.29
Wheeled fire extinguisher
2.30
2.31
2.32
Portable foam applicator unit or relevant spare tank(s)
Fire locker
Comments on use
Indicate type of extinguishing media (CO 2 for carbon dioxide, F for foam, H for gas other than CO2indicated), P for powder, W for water) and capacity (kg for gas and powder, litres for symbol. Media should be colour-coded in the lower part of the symbol as follows: grey for carbon dioxide, yellow for foam, brown for gas other than CO2, white for powder, green for water.
2for carbon dioxide, F for foam, H for gas other than CO2indicated), P for powder, W for water) and capacity (kg for gas and powder, litres for symbol. Media should be colour-coded in the centre part of the symbol as follows: grey for carbon dioxide, yellow for foam, brown for gas other than CO2, white for powder, green for water.
Indicate the number of the fire locker at the indicated in the legend.
Indicate type of extinguishing media (CO 2 for carbon dioxide, F for foam, H for gas other than CO2indicated), P for powder, W for water, S extinguishing system) and capacity (kg for gas and powder, litres for water and foam) at the top of the symbol. Add suffix “L” system. Media should be colour-coded in other than CO2, white for powder, green pressure water extinguishing system.
Space or group of spaces protected by fire-extinguishing system
I:\ASSEMBLY\23\RES\952.DOC
A 23/Res.952
No. Graphical symbol 2.33
2.34
- 12 - Reference
Water fog applicator
Comments on use
2.35
Emergency source of electrical power (generator) Emergency source of electrical power (battery)
Emergency switchboard
2.36
2.37
2.38
2.39
Air compressor for breathing devices
Control panel for fire detection and alarm system Push
button/switch for general alarm
2.40
Manually operated call
point
The use of this symbol is optional at the discretion of the competent authority.
I:\ASSEMBLY\23\RES\952.DOC
No. 2.41
- 13 - A 23/Res.952
Graphical symbol
2.42
2.43
2.44
Reference
Space or group of spaces monitored by smoke detector(s)
Space or group of spaces
monitored by heat detector(s)
Comments on use
The space(s) should be identified.
The space(s) should be identified.
Space or group The space(s) should be identified. of spaces monitored by flame detector(s)
Space monitored
by gas detector(s)
Graphical symbols for means of escape and escape-related devices
3.1
Primary escape
route
3.2
Secondary escape route
3.3
Emergency Indicate the quantity of the EEBDs stowed escape breathing at the right side of the symbol. device (EEBD)
__________
I:\ASSEMBLY\23\RES\952.DOC