压力容器英语专业常用词汇
压力容器英语专业常用词汇
用户技术条件
数据表
设计依据 设计规范 安全系数 设计压力 设计温度 操作压力 操作温度
最大许用工作压力Customer ’s specification; user ’s design specification data sheet design basis design specification safety factor design pressure design temperature operating pressure operating temperature maximum allowable working pressure
(MAWP )
最大许用外部工作压力(MAEWP ) 最低设计金属温度(MDMT ) 风载
地震荷载 腐蚀裕量 设计寿命 接头系数 介质特性 易燃易爆 有毒
极度或高度危害 常压
试验压力 立式
卧式
试验温度 装配图
竣工图
剖面
视图
尺寸公差 按比例
纵向应力 环向应力 薄膜应力
一次应力 二次应力 局部应力 峰值应力 弯曲应力 剪应力
拉伸应力 压缩应力 许用应力 弯矩
疲劳
按规则设计 按分析设计 有限元
计算书
审核
校准 maximum allowable external working pressure minimum design metal temperature wind load seismic load; earth quake load corrosion allowance design life joint efficiency medium characteristic flammable; explosive toxic extreme or high toxic substances atmospheric pressure test pressure vertical type horizontal type Test temperature Assembly drawing As-built drawing section View Dimensional tolerance Prorate Longitudinal stress Circumferential stress Membrane stress Primary stress Secondary stress Localized stress Peak stress Bending stress Shear stress Tensile stress Compressive stress Allowable stress Bending moment Fatigue Design be rules Design by analysis Finite element Calculation sheet Review Check
批准
注册执业工程师 授权检验机构 授权检验师
经授权检验师确认 设计报告 设计变更 材料代用 公称厚度
公称管径(NPS ) 成形后最小厚度 设计公式 设计输入
设计输出 设计验证 风险评估报告 传热计算 振动分析 有毒气体 有毒液体 有害
内压
外压
凹面受压封头 凸受压封头 压差
表面粗糙度 表面堆焊层 表面堆焊加硬层 除非其它方面另有规定
采购方批准前不允许
静、动和热载荷 最大允许轴向载荷 轴向刚度 轴向热膨胀差 弹性模量
椎体过渡段大端转角内半径
三、材料 碳钢
碳锰钢 Approve Registered professional engineer Authorized inspection agency Authorized inspector Certified by AI Design report Change in design Material substitution Nominal thickness Nominal pipe sizes Minimum thickness after forming Design equation; design formula Design input Design output Design verification Risk assessment report Carbon steel Carbon-manganese steel
低合金钢 高合金钢 低温用钢 耐热钢 耐蚀钢 耐腐蚀衬里 铁素体不锈钢 奥氏体不锈钢 马氏体不锈钢 双相不锈钢 抗硫化氢钢 复合板 铁基材料 非铁基材料 镍基合金
四 制造 划线 切割 刨边 坡口加工 扳边 预弯 热切割 拼接 拼接板 冷成形 热成形 皱折 组对
拼接焊封头
拼接补强板 管口方位 管标号 开孔 开孔补强 跨中 椭圆度 错变量 棱角度 直线度
接管伸长长度 车
刨
铣
镗 Low alloy steel High alloy steel Steel for low temperature service Heat resisting steel Corrosion resisting steel Corrosion resisting lining Ferritic stainless steel Austenitic stainless steel Martensitic stainless steel Duplex stainless steel Hydrogen sulfide-proof steel Clad plate Ferrous material nonferrous material Nickel-based alloy Layout Cutting Edge preparing Joint preparation Tapered edge Preliminary rolling Thermal cutting Patched up Welded plate Cold forming Hot forming Wrinkle Fit-up Bulid-up head;head consisting of several welding sections Segmented reinforcement plate Nozzle orientation Schedule number Opening Reinforcement of opening To be straddled on;straddle Out of roundness Off set Peaking Straightness Projection of nozzle Turning Planning Milling Boring
钻
垂直度 垂直度公差
螺纹精度 外观 机械损伤 划伤 划痕 去毛刺 倒棱
局部划痕或刻槽径向 环向 单壁单层 轮廓;外形 长度 高度 宽度 厚度 直径 半径 重心
不干胶标签
Drilling Perpendicularity Perpendicularity tolerance Thread precision Appearance Mschanical defect Scuffing Scratch mark;score Burring Chamfering Local crack or cutting trace Meridian direction Circumferential direction Single wall Contour Length Height Depth Thickness Diameter Radius Center of gravity