数控机床m代码含义
M00 程序停
;M00 Programmable stop
;M01 程序选择停
;M01 Selective programmable stop
;M03 主轴顺时针转
;M03 Rotate spindle clockwise
;M04 主轴逆时针转
;M04 Rotate spindle counterclockwise
;M05 主轴停
;M05 Spindle stop
;M06 换刀*
;M06 Tool change Start *
;M09 切削液关（所有）
;M09 Coolant off (all coolants)
;M10 B轴夹紧
;M10 Clamp B-axis
;M11 B轴松开
;M11 Unclamp B-axis
;M12 Start pallet change *
;M12 托盘交换*
;M20 A轴夹紧
;M20 Clamp A-axis
;M21 A轴松开
;M21 Unclamp A-axis
;M51 变量：穿过主轴冷却液
;M51 VARIANT: High pressure coolant through spindle
;M52 变量：淋浴冷却液
;M52 VARIANT: Coolant shower
;M53 VARIANT: Air through spindle on (on I y when minimum quantity lubrication)
M53 变量：穿过主轴空气开（只有当最小量润滑时）
;M54 VARIANT: Minimum quantity lubrication on
M54 最小量润滑开
;M55 穿过主轴冷却液监控开
;M55 VARIANT: High pressure coolant monitoring on
;M56 穿过主轴冷却液监控关
;M56 VARIANT: High pressure coolant monitoring off
M57 选择：过程测量开
;M57 OPTION: In process measuring on
M58 选择：过程测量关
;M58 OPTION: In process measuring off
;M59 设定工件？
;M59 Set part is machined
;M61 托盘 夹紧*
;M61 Clamp pallet *
;M62 托盘 松开*
;M62 Unclamp pallet *
;M65 钻空检查*
;M65 OPTION check drill *
;M69 托盘交换完成*
;M69 Pallet change finished *
;M71 换刀门关闭
;M71 Close tool change door
;M72 换刀门打开
;M72 Open tool change door
;M75 钻头断刀控制: 检查立刻放下刀具？
;M75 OPTION drill break control: check lay down tool immediately ;M76 刀具断刀控制: 检查被标记的刀具？
;M76 OPTION tool break control: check tool of marked place *
;M77 刀具断刀控制:放下刀具时在刀库区作标记
;M77 OPTION tool break control: mark magazine place of lay down tool * ;M78 钻头断刀控制检查*
;M78 OPTION check drill break control *
;M85 Umspeichermerker Spindel --> Magazin 1 setzen *
;M85 Restore flag spindle --> set magazine 1 *
;M86 Umspeichermerker Spindel --> Magazin 1 ruecksetzen *
;M86 Restore flag spindle --> reset magazine 1 *
;M87 Werkzeugmagazin freigeben von Bearbeitung
;M87 Enable tool magazine from machining
;M88 装刀启动*
;M88 Toolload started *
;M89 卸刀启动*
;M89 Tool unload started *
;M90 装刀 /卸刀 完成*
;M90 Toolload I unload finished *
;M91 刀具卡爪关闭*
;M91 Close tool gripper *
;M92 刀具卡爪打开*
;M92 Open tool gripper *
;M93 主轴紧刀*
;M93 Clamp spindle collet *
;M94 主轴松刀*
;M94 Unclamp spindle collet *
;M96 主轴速度监控关*
;M96 Spindle speed monitoring off *
;M97 主轴速度监控开*
;M97 Spindle speed monitoring on *
;M98 打开循环计时器
;M98 Start cycle time counter
;M99 关闭循环计时器
;M99 Stop cycle time counter
;
;
;M151 选择切削液5bar
;M151 OPTION selection coolant 5 bar
;M152 选择切削液10bar
;M152 OPTION selection coolant 10 bar
;M153 选择切削液17bar
;M153 OPTION selection coolant 17 bar
;M154 选择切削液25bar
;M154 OPTION selection coolant 25 bar
;M155 选择切削液33bar
;M155 OPTION selection coolant 33 bar
;M156 选择切削液40bar
;M156 OPTION selection coolant 40 bar
;M157 选择切削液50bar
;M157 OPTION selection coolant 50 bar
;M161 VARIANT: Minimum quantity lubrication select pressure step 1 M161 最小量润滑选择压力1
;M162 VARIANT- Minimum quantity lubrication select pressure step 2 M162 最小量润滑选择压力2
;M163 VARIANT: Minimum quantity lubrication select pressure step 3 M163 最小量润滑选择压力3
;Erweiterte M-Funktionen XHC 241 SIN 840D
;============================================================= ;
;M1=44 以手动断刀检测为条件启动*
;M1=44 OPTION: Check start conditions for manual tool break control * ;M1=45 以手动断刀检测循环完成*
;M1=45 OPTION: Cycle manual tool break control finished *
;M1=48 Freigabe Vorrichtung entkuppeln
;M1=49 暖机程序完成 *
;M1=49 OPTION: Warm-up program finished *
;M1=50 托盘交换循环启动*
;M1=50 Pallet change cycle started *
;M1=51 预先控制托盘夹紧*
;M1=51 Precontrol clamp pallet *
;M1=52 预先控制托盘放松*
;M1=52 Precontrol unclamp pallet *
;M1=53 左侧装置冲洗 *
;M1=53 PCH rinse lifting device *
;M1=54 Z轴进给启动（相反的程序）*
;M1=54 Feed enable Z-axis start from reverse program *
;M1=55 Z轴进给停止（相反的程序）**
;M1=55 Feed enable Z-axis stop from reverse program *
;M1=56 Startvoraussetzung fuer Palettenwechsel fehlt *
;M1=56 Start condition for pallet change missing *
;M1=57 激活断刀控制*
;M1=57 Activate tool break control *
;M1=58 在断刀后取消刀具交换
;M1=58 Cancel tool change from tool break control *
;M1=59 Pruefen ob Altplatz an Wechselstelle *
;M1=59 Check if old place at change position *
;M1=60 OPTION: Spare for BLUM drill break control laser on * ;M1=61 OPTION- Spare for BLUM drill break control laser off * ;M1=62 OPTION: Spare for BLUM drill break control open cap * ;M1=63 OPTION: Spare for BLUM drill break control close cap * ;M1=64 启动主轴切削液
;M1=64 Start blow off coolant from spindle
;M1=65 停止主轴切削液
;M1=65 Stop blow off coolant from spindle
;M1=66 REV (Freifahrprogramm) NC-Kanal 1 begonnen *
;M1=66 REV (reverse program) CN-channel1 started *
;M1=67 REV (Freifahrprogramm) NC-Kanal 1 beendet / Reset * ;M1=67 REV (reverse program) CN-channel1 finished I Reset * ;M1=70 主轴短暖机程序激活*
;M1=70 Spindle short warm-up cycle is active *
;M1=71 主轴短暖机程序循环完成 *
;M1=71 Spindle short warm-up cycle finished *
;M1=72 主轴长暖机程序激活**
;M1=72 Spindle long warm-up cycle is active *
;M1=73 主轴长暖机程序循环完成 *
;M1=73 Spindle long warm-up cycle finished *
;M1=74 主轴暖机程序被低温激活*
;M1=74 Spindle warm-up cycle of low temperature is active * ;M1=75 主轴暖机程序被低温激活后循环完成 *
;M1=75 Spindle warm-up cycle of low temperature finished * ;M1=76 机床暖机循环后关闭*
;M1=76 OPTION: Machine off from warm-up cycle *
;M1=77 开始时间监控器主轴使用10分钟 *
;M1=77 Start time monitoring spindle in use 10 minutes *
;M1=78 开始时间监控主轴使用15分钟 *
;M1=78 Start time monitoring spindle in use 15 minutes *
;M1=79 开始时间监控主轴使用60分钟 *
;M1=79 Start time monitoring spindle in use 60 minutes *
;M1=80 托盘交换请求*
;M1=80 Pallet change desired *
;M1=81 PCH 使能从暖机循环 *
;M1=81 PCH enable from warm-up cycle *
;M1=82 暖机循环中主轴倍率100%打开
;M1=82 Spindle override 100% on from warm-up cycle *
;M1=83 暖机循环中主轴倍率100%关闭
;M1=83 Spindle override 100% off from warm-up cycle *
;M1=84 暖机循环持续激活
;M1=84 Warm-up cycle is still active *
;M1=85 开始时间监控主轴使用30分钟 *
;M1=85 Start time monitoring spindle in use 30 minutes *
;M1=86 启动主轴装卸刀循环使能*
;M1=86 Start enable cycle load I unload tool via spindle * ;M1=87 用主轴装刀激活*
;M1=87 Load tool active via spindle *
;M1=88 用主轴卸刀激活*
;M1=88 Unload tool active via spindle *
;M1=89 刀库旋转*
;M1=89 Rotate tool magazine *
;M1=90 刀库在位 *
;M1=90 Tool magazine in position *
;M1=91 Altplatz zur Wechselstelle positionieren *
;M1=91 Position old place to change position *
;M1=92 Startvoraussetzung fuer Werkzeugwechsel fehlt *
;M1=92 Start condition for tool change missing *
;M1=93 Spindel freigeben fuer Spindel referenzieren *
;M1=93 Spindle enable for referencing spindle *
;M1=98 Reserviert fuer Maschinendauerlauf mit autom. Werkstueck spannen *
;M1=98 Spare for machine continuous cycle with autom. part clamp * ;M1=99 Reserviert fuer Maschinendauerlauf mit Palettenwechsel * ;M1=99 Spare for machine continuous cycle with pallet change * ;
;M-Funktionen K2 XHC 241 SIN 840D
;============================================================= ;
;M64 请求启动监控器在通道2检查钻头
;M64 OPTION: Request start enable cycles check drill CN-channel 2 * ;M65 在通道2检查钻头**
;M65 OPTION: Check drill CN-channel 2 *
;M66 Bohrer pruefen beendet NC-Kanal 2 *
;M66 OPTION: Check drill finished CN-channel 2 *
;M71 Rev-Progr. (Freifahrprogramm) NC-Kanal 2 begonnen *
;M71 Rev-progr. (reverse program) CN-channel 2 started *
;M72 Rev-Progr. (Freifahrprogramm) NC-Kanal 2 beendet *
;M72 Rev-progr. (reverse program) CN-channel 2 finished *
;M78 监控器在通道2检查钻头*
;M78 OPTION: Monitoring start check drill CN-channel 2 *
;M91 刀具卡爪关闭**
;M91 OPTION: Close tool gripper *
;M92 刀具卡爪打开**
;M92 OPTION: Open tool gripper *